Page-30 H&H Classic Parts Q&A

Asked 4 ´months ago | Front Disc Brake Kit (6 Lug)

Dynacorn shows this as for the V8 motor. No listing for the 6 cly. View answer

Asked 4 ´months ago | Throttle Linkage

1966 Cutlass buckets seats View answer

Asked 4 ´months ago | Transmission Hump Console Tan

Is this product compatible with 1957 Bel-Air vehicles? View answer

Asked 5 ´months ago | Nu-Relics Power Vent Window Kit

Is this product compatible with 1956 150 vehicles? View answer

Asked 5 ´months ago | Nu-Relics Power Vent Window Kit

Mine in the upper right hand corner has a 5. The backplate is stamped 105. What does this tell me. View answer

Asked 4 ´months ago | Neutral Safety Switch

Is this product compatible with 1955 Bel-Air vehicles? View answer

Asked 5 ´months ago | Nu-Relics Power Vent Window Kit

What type of motors are used in this product? View answer

Asked 5 ´months ago | Nu-Relics Power Vent Window Kit

Does the bezel come with this, or is it ordered separately? View answer

Asked 4 ´months ago | Clock

What about left-hand door skin? View answer

Asked 4 ´months ago | Door Skin RH (OEM)

Are the spindles compatible with a 1966 Bel-Air? View answer

Asked 5 ´months ago | 2

do this fit convertible View answer

Asked 4 ´months ago | Emergency Brake Idler Lever Floor Mount

What mounting hardware is required for this part View answer

Asked 4 ´months ago | Lower Grille Molding

Are the spindles compatible with a 1965 Bel-Air? View answer

Asked 5 ´months ago | 2

is this any different from 72 ss chevelle View answer

Asked 4 ´months ago | Complete Console Kit

What material are the moldings and what color is in the middle? It looks like yellow? View answer

Asked 4 ´months ago | Side Molding Set

is there a top or bottom distinction on these? View answer

Asked 4 ´months ago | Rear Stock Height Coil Springs

Are the spindles compatible with a 1970 Caprice? View answer

Asked 5 ´months ago | 2

Well this mirror pull in so the driver can see the right side of the car View answer

Asked 4 ´months ago | Outside Mirror RH

Are the spindles compatible with a 1968 Caprice? View answer

Asked 5 ´months ago | 2

What's the difference between tint and gray View answer

Asked 4 ´months ago | Side Glass Set 6 pc (Tinted)

Are the spindles compatible with a 1967 Caprice? View answer

Asked 5 ´months ago | 2

Looking for a radio that has Sirius satellite capabilities View answer

Asked 4 ´months ago | USA-630 AM/FM Radio

what type xxxx thred View answer

Asked 4 ´months ago | Gas Tank Sending Unit Screw Set

Will this fit 58 Belair View answer

Asked 4 ´months ago | Hood Latch Spring Repair Kit

Are the spindles compatible with a 1966 Caprice? View answer

Asked 5 ´months ago | 2

Are the spindles compatible with a 1965 Caprice? View answer

Asked 5 ´months ago | 2

Are the spindles compatible with a 1969 Impala? View answer

Asked 5 ´months ago | 2

Are the spindles compatible with a 1968 Impala? View answer

Asked 5 ´months ago | 2

Do u have 2 side moldings for a 63impala View answer

Asked 4 ´months ago | Complete Side Molding Set

Does this go to a 1990 Chevy?Silverado four by four fifteen hundred from the pedal View answer

Asked 4 ´months ago | Clutch Pedal Push Rod

Will these work in a 1970 GTO View answer

Asked 4 ´months ago | Nu-Relics Full Power Window Kit with Nu-Cranks

Are the spindles compatible with a 1966 Impala? View answer

Asked 5 ´months ago | 2

Are the spindles compatible with a 1965 Impala? View answer

Asked 5 ´months ago | 2

When might you get '62 impala ash tray # 15447 in again? View answer

Asked 4 ´months ago | Ash Tray

What is the drop height provided by the spindles? View answer

Asked 5 ´months ago | 2

can this be picked up, to save shipping? View answer

Asked 4 ´months ago | Trunk Lid Assembly

What condition are the spindles in? View answer

Asked 5 ´months ago | 2

How long is the roll, would it be enough to cover both sides of my trucks trim? View answer

Asked 4 ´months ago | Woodgrain Body Side Molding Decals

Will this work 1957 Chevy truck View answer

Asked 4 ´months ago | Master Cylinder Hardware Kit

i ordered the molding clip set for 1964 impala 2 door non ss. It did not come with instructions. do you have instru View answer

Asked 4 ´months ago | Complete Side Molding Clip Set

Does these have the stainless trim on the top edge? View answer

Asked 4 ´months ago | Window Wiper Kit

does the nu-cranks have a driver master switch for all 4 window's View answer

Asked 4 ´months ago | Nu-Relics Full Power Window Kit with Nu-Cranks

What brand are the spindles? View answer

Asked 5 ´months ago | 2

What is the part number of the spindles? View answer

Asked 5 ´months ago | 2

What brand is the gas cap? View answer

Asked 5 ´months ago | Gas Cap

Is the gas cap compatible with 1971-72 trucks? View answer

Asked 5 ´months ago | Gas Cap

Browse by Topic